A washing machine is the most important yet least appreciated consumer commodity that must be a part of any home. It should come as no surprise that none of us gives these washing machines much thought until they break down and interfere with our ability to clean laundry.
A family will experience the most discomfort from laundry heaps and will look for solutions to eliminate them as soon as possible.
The well-known Kenmore washer series will help you effectively clean your laundry and has freed the working class from the necessity of laundromats.
If your 500 series washer has stopped functioning for whatever reason, this troubleshooting guide will be helpful to you. The guide will offer you the simple solution you are looking for to help you troubleshoot a Kenmore series 500 washer.
Table of Contents
Kenmore series 500 washer troubleshooting
Before taking any corrective action, you must first pinpoint the source of the washer’s issue because it could be either a not-starting or a not-filling issue.
If your Kenmore Series 500 washer doesn’t start, you should follow the next three steps to get it working:
- The electrical port that connects your washer with the electricity utility lines is where you should start looking for problems with your washing machine. You must also ensure that the machine’s power switch is correctly put into the connection port.
- Checking the fuse box should come next if there are no issues with the power connection. Your washer may have stopped working for various reasons, including a blown fuse, which may be fixed by replacing the old, worn-out fuse with a new one.
- If you are connecting your washer to the utility power line using extensions, stop doing so immediately because it is a common cause of the washing machine not starting as it is commonly associated with poor connections. Instead, connect your washer directly to the power port.
If your washing machine is still not operating after undertaking the three steps above, it is time to go on to the next phase, which is the washer not filling up, and to take the necessary corrective action. This phase involves the following easy steps:
- The water valves for the Kenmore series washer are located behind the appliance, and if they are closed, the washer won’t fill with water. To fill your machine with water, you must ensure they are turned on.
- Change the washer settings that might be causing it to take longer to start by restarting the washer.
- Kenmore 500 series is designed so that if its door is not closed, it will not operate. You must ensure that the washer is closed completely and that nothing obstructs the doors. Remove any obstruction; if there is one, carefully seal it and reset the washer to resume the washing process.
Related Questions
What Could Cause a Kenmore Washer To Get Stuck on Sensing?
The most common reasons for a Kenmore washer getting stuck on the sensing mode and not moving to the wash cycle can be:
- Loose fittings
- Issues with the control board
- Wiring issues
- Issues regarding the shift actuator
- Water inlet valve issues
How Do You Fix Kenmore Washers When Stuck in Sensing?
Use the washer’s diagnostic feature first, then refer to the manual’s error code list to determine the exact problem.
If this doesn’t work, it is advised that you get in touch with an expert to identify and resolve the problems.
You may take several steps to try fixing the washer yourself if one of the issues listed above appears after the diagnostic cycle. However, you should use caution here.
If your product is still under warranty, you should contact a specialist immediately.
Due to the high cost of replacement parts, you should try gently cleaning the filter if the water entry valve becomes clogged.
A loose wire, broken door, or malfunctioning board can only be fixed by contacting the service center and ordering a replacement.
You can also try to reset the Kenmore washer to see if it resolves the issue. In some instances, if there are some software issues, a simple reset will fix the problems.
How Can a Kenmore Washing Machine Sensor Be Reset?
The procedure of resetting the sensor on a Kenmore washing machine can vary from model to model. If unsure, look at the user manual that came with your specific model or search from the official Kenmore washing machine website.
However, there are often two approaches to system resets. Not to worry! Both of these are pretty simple.
The washer must be turned off and unplugged from the power source.
The ideal time to wait before plugging it back in and restarting the machine is 5 to 10 minutes. This should work for a simple reset.
The second way is likewise straightforward; you must repeatedly press the stop button before pressing the power button.
The next step is to choose any wash cycle and then press the start button. After running the cycle, you should restart your washer.
You should contact the company or the official service center if the issue is still not resolved even after following the above steps.
How Can You Tell if the Shift Actuator is Defective?
Excessive grinding noises before the start of the washing cycle or a sluggish tub and agitator are two of the most typical symptoms of a bad shift actuator.
Run a diagnostic tool if there is a problem and check the error number with the company as one approach to learn more.
Is There a Distinction Between Precise Fill and Auto Sensing?
Although these two terms are frequently used interchangeably, precise fill fundamentally refers to the process by which a washer determines the correct volume of water to use for each load.