Skip to Content

Troubleshooting Common Husqvarna 572XP Chainsaw Issues

Husqvarna 572XP Chainsaw Issues, With the Husqvarna 572XP chainsaw, you can easily change the look of your woodwork. The best part about proudly wielding this multifunctional instrument is that with a few carvings, you may go for any trend, old-fashioned or futuristic.

Even the best chainsaws, however, are subject to normal wear and tear. As a result, in this article, we’ll discuss Husqvarna 572XP common issues and walk you through thorough remedies to these common issues.

Typical Problems Associated with Husqvarna 572XP Chainsaw

Husqvarna 572XP Chainsaw Issues

A list of frequent Husqvarna 572XP problems that will be explored in this article is provided below:

  • Compression problems
  • Airflow problems
  • Spark problems
  • Fuel supply problems

Let’s take a closer look at the problems now that you have a general overview of them.

Compression Problems

Husqvarna 572XP Chainsaw Issues the chainsaw refuses to start as you tuck the starter line, the compression could have an underlying problem.

A Husqvarna 572XP chainsaw has a lot of moving parts because it’s a fuel-powered machine. You will be in trouble when the required amount of compression isn’t enough to keep these junctions going.

When compression availability is low, unplanned shutdowns and power decrease occur. Placing the chainsaw on flat ground and lifting the starter rope device is a simple technique to check for decreased compression. If the compression is too low, the chainsaw cord will continue to lengthen, failing to sustain the weight and eventually pull-out completely.

The next step would be to inspect the crankshaft seals for air leaks. Piston collapses could also be the cause of this ailment.

A faulty crankshaft seal or gasket most commonly causes compression difficulties. As a result, if any of these internal components are broken, cracked, or damaged, the chainsaw will need to be completely disassembled to resolve the issue.

Needless to say, it’s not a job for a do-it-yourself, so get a pro.

Air Flow Problems

The combustion chamber’s performance can be significantly aided or hindered by air pressure and flow. Some even claim that the air filters in this machine work as lungs.

Airflow problems will result in machine failure or a sputtering start. Take advice from your user manual and inspect the air filter for dirt and grime build-up to see if it’s working correctly. Check for debris accumulation in the muffler as well. If your air filter isn’t working correctly, it’s recommended to replace it.

Remember that air filters are in charge of preventing airborne impurities from obstructing the chainsaw’s efficiency; therefore, they should not be overlooked.

Spark Problems

Husqvarna 572XP Chainsaw Issues the fuel fails to ignite, your chainsaws will be unable to start. Without a spark, this moderation is likewise impossible.

 Locate and remove the lid from the chainsaw’s spark plug, to check for sparks. Remove the spark plug from the cylinder and connect the spark plug wire to the cylinder without replacing the spark plug.

Ensure that the electrode top of the spark plugs comes into contact with a metal façade on the engine before stretching the chainsaw cord. It’s a well-oiled machine if you detect a spark. If this is not the case, inspect the spark plug electrode for waste, precise spacing, corrosion, and carbon build-up.

The first approach is to clean the spark plug with a dampened cloth thoroughly, let it dry, then try it again. If the problems persist, check the spacing between the spark plugs. If the gap appears more extensive than expected, replace it with a new model to restore the chainsaw’s functionality.

Fuel Problems

Husqvarna 572XP Chainsaw Issues

When problems with the fuel occur, you must quickly inquire about the fuel mix, carburettor settings and inspect the compartment for damaged lines and clogs.

To begin, make sure you have the standard fuel mix by entirely replacing the contents of the fuel container. Even if you have the correct combination, the contents can get contaminated if left inside for an extended period.

On the other hand, if you observe that the fuel filter is clogged, you can use a fuel cleaner system. Fill the tank with the gasoline cleaner system and let it sit for a few hours. After that, start the chainsaw and allow the fuel to spread evenly throughout the instrument to clear any lingering obstruction.

Another critical step is to inspect the gasoline line for cracks and breakage. This internal and efficient line prevents wood chips, dirt, and oil from entering the system and interfering with the fuel supply. However, fuel lines can become brittle as their years of operation increase.

Pull out a part of the fuel line to check and eliminate faults with the fuel filter.

Pro tip: Don’t use too much pressure on the line, and only expose a tiny portion of it. If you discover any damage or blockage, you will need to replace it with a fresh filter.

Pull out the old filter, twist it, and then feed in the new one to your chainsaw.

Troubleshooting Tips

The Husqvarna 572XP specifications are unrivalled. That is why so many individuals are devoted admirers. Unfortunately, this machine still has a limit on its components. When things aren’t functioning well, it’s always a wise decision to check by elimination.

The airing, spark, and gasoline systems are just a few components that could lead to a chainsaw breakdown. Still, let’s break it down a little more. Here are some basic assessments that can assist you in determining the chainsaw’s problems:

  • If you find discrepancies in the compression, remove the exhaust to check for piston seizures or ring damage
  • Inspect the cylinder base gasket, hoses, and manifold for leaks
  • Double-check the spark plug electrode if you see carbon accumulation or general wear
  • While working, keep an eye out for any unusual sparks in the system
  • Don’t skimp on carburettor adjustments, including the idle setting
  • Check the air filter systems for blockages regularly
  • It would help if you also kept an eye on the gasoline delivery line for cracks and blockages.
  • If you’re suffering from a blockage, don’t forget to look at the fuel filter as well.
  • Always use the appropriate gasoline mix when refilling or replacing your tank. Never cut corners when it comes to quality.
  • Tuck the starter rope in to check the compression and engine adequacy.