KitchenAid Dishwasher Start Button Issues are one of the most valuable appliances a home can own. Although KitchenAid dishwashers are built to be highly durable and perform well in most situations, there can occasionally be issues, such as malfunctioning the power button or start button. There are several causes for this issue. Regardless, taking good care of your KitchenAid dishwasher can lessen the likelihood of these issues.
However, if the start button on your KitchenAid dishwasher is not working, you might be in desperate need of some troubleshooting techniques. The next section of this article will walk you through troubleshooting a Kitchenaid dishwasher with a start button that is not working.
Table of Contents
How To Fix a Kitchenaid Dishwasher Start button that is Not Working
Control Lock is Active
If you push the start button of your Kitchenaid dishwasher and the dishwasher does not start, check whether the control lock is turned on. If the control lock is on, it must be turned off immediately.
Pushing and holding the power button for four to five seconds will enable you to turn off the control locking mode.
Keep your attention on the red control bulb next to the keys on the control board. The bulb will flash three times before going off, signaling that your attempt was effective. You can start a new wash cycle in the dishwasher when the light goes off.
Sleep Mode is Active
Pressing the power button on your Kitchenaid dishwasher turns the device to sleep mode, and the washer will not function as a result.
Make sure your KitchenAid dishwasher is not in sleep mode when operating it. If the machine is in sleep mode, it will not start immediately if no continuous source of freshwater is attached.
Delayed Wash is Active
A child or you mistakenly choosing the delayed wash option can cause the KitchenAid dishwasher to hesitate before starting.
The delayed wash feature can be stopped by hitting the power button on your Kitchenaid dishwasher.
The Kitchenaid Dishwasher Not Well Closed
The power key on a KitchenAid dishwasher won’t work if the lid is not completely sealed. Make sure the lid is tightly closed.
Note that your KitchenAid dishwasher has a bottom shelf that is placed reverse, which could cause the lid to lock and result in an improper seal.
There is No Water Supply
Many individuals forget to turn on the water supply before running the dishwasher. The dishwasher won’t start no matter how long you hold down the power button before turning on the water supply.
Consult the instructions for your gadget if you’re unsure how to turn on the water supply.
Electrical issues
Verify that the dishwasher is on and that the wire is securely connected to the power source. The dishwasher can become unusable if there are power surges.
It’s possible that the dishwasher won’t work because it’s not plugged in or because the fuse box tripped. Verify that the dishwasher is properly connected and that no fuses have been damaged recently.
Incorrectly Functioning Timer
The dishwasher’s timer is crucial to how well it functions. Without kitchenaid dishwasher start Button Issues, energy does not flow through the appropriate areas at the appropriate times.
KitchenAid Dishwasher Start Button Issues schedule is not followed, power won’t be sent to the dishwasher, prohibiting it from starting. Timers are commonly misunderstood; therefore, check for other frequently broken equipment while changing the timer.
How To Reset a Kitchenaid Dishwasher
You might potentially encounter functional problems with your KitchenAid dishwasher. Here is where a reset is frequently required.
The following sequence will work on many KitchenAid dishwasher models, even if the precise reset procedure may vary by model. For your Kitchenaid dishwasher to be reset:
- Simultaneously press the “Hi-temp Scrub” and “Energy Saver Dry” buttons five times
- The control panel display’s lights should flash rapidly for 4-5 seconds after you have finished
- After that, allow the appliance to sit for 10 minutes so the dishwasher can reset
- Once it has reset, attempt starting a fresh cycle
Can You Manual Reset a Kitchenaid Dishwasher?
Yes. You can manually rest your Kitchenaid dishwasher. Unhook the dishwasher unit’s power cord and leave it unplugged for around 5 minutes to do a manual reset. Doing this will give the dishwasher’s computer time to reset.
Reconnect the power cord after that, then check the display panel to see if the error codes have disappeared.
Why is Your KitchenAid Dishwasher Beeping?
Thanks to the sensor, the dishwasher will beep to alert you that the washing cycle has been interrupted by something.
The likelihood is that the door latch needs to be connected or that the door has to be completely closed.
The beeping may also indicate that a component inside the device is failing. Additionally, the beeping may indicate that it’s time to take the dishes from the machine and finish the cycle.
What Does a KitchenAid Dishwasher’s Blinking Blue Light Indicate?
Depending on the model, a blinking blue light on a KitchenAid dishwasher could indicate several different things.
The most frequent causes, however, are a control panel defect, a component failure, or the door latch interrupting the wash cycle. The easiest way to determine the cause of the blinking light is to consult your user handbook.
How Do You Run a Diagnostic for your KitchenAid Dishwasher?
It varies. Each KitchenAid dishwasher could have a different procedure for starting the diagnostic mode. Consult your user manual to get the particular instructions for your dishwasher model.
The steps for three well-known Kitchenaid dishwasher models are listed below:
- Kitchenaid Model KUDD03DT
For this specific model, you must first click the “High Temp Wash” button six times before pressing the”Start” button eight times. Keep in mind that you must rapidly push these buttons.
- Kitchenaid Model W10142800B
On this model, while the device is in standby mode, press “Heated Dry” and “Normal” twice consecutively to start the diagnostic process.
- Kitchenaid Model 8572216
The procedure for running a diagnostic for this particular model is similar to that of Kitchenaid Model W10142800B.
Final Take
Dishwashers made by KitchenAid are among the most durable ones available. They do, however, experience tech issues just like any other brand.
If the start button of your Kitchenaid is not working, then the troubleshooting tips in this article will be useful to you.