Skip to Content

Fixing Common Speed Queen Washer Problems: Solutions

Speed Queen washer problems, The washers from Speed Queen are long-lasting. This might be the reason why they get consistently positive reviews from customers. But just like any other appliance in your home, these washers have problems too. This article will walk you through the most common issues you are likely to encounter if you are a Speed Queen Washer owner and how to fix them.

Speed Queen Washer Problems: How to Solve Them

Speed Queen washer problems

Speed Queen Washer Not Draining

This is a typical issue that frequently affects top-loading Speed Queen washing machines.

Typically, a faulty drive belt is the issue’s primary cause.

For the belt to spin the washer with enough force, it must be under significant tension. However, the belt will eventually deteriorate and lose all the tension required to perform its function.

The washer cannot spin as quickly with insufficient belt tension. Because of this, the washer won’t be able to completely drain the water from the load of laundry you’ve placed inside.

This issue is most apparent when you load the washer with a large load of clothing.

Very little water can be spun off the load and drained out of the tub without sufficient belt tension.

Drive belts that are worn out must be replaced, which can be a challenging task. Let’s divide it into two steps: getting access and changing the belt.

The belt will be on the lower end of a top-load washer, so you will need to remove the panel and any other obstructions to gain access.

The user manual for your specific machine should be consulted if you need more guidance on gaining access.

You’ll discover that removing the old belt is considerably easier than installing the new one when you can plainly see where the belt is. This is because a new belt will be tauter than an old one.

Slip one end of the belt around the drum pulley. The other end of the belt will then need to be looped around the motor pulley with a little push.

Once you’ve done so, manually rotate the washer to check that the belt is correctly positioned on both pulleys.

To replace the belt, remember that you must first turn off the power supply.

Speed Queen Washer Not Filling With Water

Your Speed Queen washer’s inability to fill with adequate water to wash a load of laundry is a frequent issue.

The two potential reasons for this are a problem with the water entry valve or the washer’s timer.

If the water inlet valve is broken, it might not be fully open to allow enough water. This might result in water entering the tub, but not enough to start the wash cycle.

Sometimes the water entry valve functions flawlessly, but the timer is the issue. Keep in mind that the timer will organize the various parts to do their responsibilities in the proper order.

There might not be enough water in the tub if the timer fails to instruct the inlet valve to open.

It is best to replace the water inlet valve and timer completely because neither can be repaired.

Thankfully, doing so is not too difficult. Consult your user manual to order the proper replacement for the timer or the inlet valve.

Before repairing either of these parts, you should first unplug the unit’s power source.

Also, ensure you shut off the water supply while repairing the water inlet valve. Afterwards, put a cloth below it to catch any water that might leak out.

To start, remove the access panel and locate the component that must be changed. A mounting plate and screws are typically used to secure a water inlet valve. You must first get rid of those.

Replace the old part with the new one after removing the electrical connectors. Reconnect everything as before and replace all the screws you removed earlier.

Speed Queen washer Not Spinning Fast Enough

A Speed Queen washer needs more than just spin to function correctly. Additionally, it must turn at the proper rates.

Your washer might occasionally be in operation but never reach the proper speeds. That could be the result of a vibration sensor issue.

A thorough examination of the wiring is necessary to resolve the issue. You might need to solder the wiring and apply a heat shrink to improve the connection if there are any breaks or cracks along the line.

Speed Queen Washer Stops Mid Cycle

Most frequently, some customers find that their Speed Queen washer fails in the middle of a cycle.

That might result from a broken lid or door switch, mainly if the machine is spinning faster and producing more strange vibrations.

To fix this issue, you’ll need to replace the door switch assembly or the lid switch.

You can locate the lid switch by removing the access panel after cutting off the electricity.

It can be replaced in a short amount of time by simply unplugging the power connector and removing any mounting hardware that is holding it in place.

Then work backward by replacing the connectors and mounting screws after installing the new switch.

The Speed Queen washer is making noise

Speed Queen washer problems

The Speed Queen washer also frequently experiences issues with excessive noise coming from inside the appliance during a cycle. You’ll typically hear this as a high-pitched squealing or grinding sound when the washer is agitating or spinning. If this is the case, the belt or idler pulley may be malfunctioning.

A brand-new pulley will be necessary to solve this issue. Although it requires many more steps than changing most other parts, you can do it yourself if you buy a belt and idler pulley kit for your Speed Queen washer model. You must unplug the device and then try accessing the pulley. That might entail taking out the existing drive belt and the access panels.

Usually, a bolt that requires some effort to remove holds the pulley in place. However, repairing the new pulley shouldn’t be too challenging once it is removed. Once it’s on, you’ll have to go backwards and replace the earlier-removed access panel and the drive belt.

Final Take

There you have it. Some of the best washing machines available are made by Speed Queen.

You’ll be able to maximize the use of your washer after you understand the typical issues to anticipate and how to address them.