GE Washer Drain and Spin Issues, A washer is a popular appliance among households everywhere. Due to its wide use, issues with GE washers are common and easy to resolve when properly treated. However, they can be a huge problem if not dealt with in time.
Table of Contents
GE washer not Draining or Spinning: Easy to Follow Troubleshooting Guide
Sometimes, the machine just won’t drain, spin, or operate properly. Below is an easy-to-follow troubleshooting guide should your unit stop spinning or will not drain.
Check the Drain Pump filter for Foreign Objects
GE Washer Drain and Spin Issues your washer is not draining, the first thing to check is the drain pump filter. This is located at the bottom of the machine under the front panel. You will need to remove the front panel to access it.
Once you have removed the front panel and access the drain pump filter, look inside for any foreign objects that may be stuck there. If you see any foreign objects, clean them out with a long-handled brush or a drinking straw.
If there are no foreign objects in there, check to ensure that there aren’t any kinks or clogs in your drain hose leading from your washing machine to your main drain line, which goes outside. Once again, clean out debris with a long-handled brush or a drinking straw.
GE Washer Drain and Spin Issues checked both of these things and still cannot get your washer to drain water properly, check the other troubleshooting ways to fix them.
Inspect the Drain hose for Clogs or Kinks
If your washing machine is not draining or spinning, you should check the drain hose first. You can do this by disconnecting the drain hose from the back of your washing machine and checking for clogs or kinks. Remove any obstructions and reattach the drain hose to your appliance.
If you don’t see any debris in your drain hose, try turning off your water supply valve and opening up all your home faucets. If you have a water softener, turn it off as well. Then turn on the water supply valve again, and watch for water to come out of all faucets. Another issue with your plumbing system may need professional attention if no water comes.
If there is no blockage in the drain line, there could be something wrong with your pump – usually caused by a faulty control board or timer motor. When this happens, it’s best to contact an experienced technician who can diagnose what went wrong with your appliance and provide repair services accordingly.
Replace the Drain Hose if Damaged
If your GE washer is not draining, you may need to replace the drain hose. The drain hose connects to the back of your machine and should be replaced if it is damaged or cracked. This allows your washer’s drain pump to push water out of the tub.
If you have a newer model, you may have an internal drain pump instead of a separate hose. In this case, look for a small round hose that goes from the back of your machine up into it. If this hose is damaged or broken, it can cause your washing machine not to drain properly or at all.
Clean out the Drain Pump Filter
The drain pump filter is located on the bottom of the washer and is a small filter that can get clogged. To access it, place a towel or cloth down and tip the washer over to remove the screws that hold the bottom panel in place. Remove the panel and clean out any debris or lint that may have accumulated in there.
If you have already done this and still have an issue, you should check to ensure nothing is blocking the drain hose where it connects to your wall. This can also cause your washer not to drain properly.
The Pressure Switch Might be Defective
The pressure switch is a safety device that prevents the washer from draining water if the door is opened during the cycle. If it’s defective, it could be causing these symptoms.
The pressure switch can become defective if exposed to too much moisture or if something gets inside and causes it to malfunction.
The first thing you should do is check for any obvious signs of damage or wear. If there are no obvious signs of damage, remove the front panel and check for water leaking into or around the washer. If there’s no sign of water leakage, your problem may be due to a faulty drain pump or drain hose.
The Motor Control Board Might be Defective
The motor control board is the brain of your washing machine. It tells the machine when to move and stops when the cycle is complete. If the control board senses a problem, it can shut down the washer prematurely or prevent it from spinning.
Turn off and unplug your washer to try this. Remove the cover from your washing machine and look for two wires linked to two plugs on either side of a circuit board in the top.
The circuit board should contain one centre plug and two ends plugs. The plug on one end has four wires, while the other has three. Before testing your circuit board, make sure both connectors are fully inserted to avoid shorting anything out by touching them.
Turn on your washer again and wait until it fills with water for about 30 seconds. When the water level reaches its highest point, unplug your washing machine again and check whether any one wire feels warm or hot to
Final Word
Any obstruction is likely to cause GE washer not to drain or spin. A spin cycle removes the largest amount of water from the clothes, so if an obstruction is caused by a foreign object such as clothing or part of the drain hose itself, it will also affect the draining process. In these instances, you’ll need to clear the obstruction.